3

I have several neckties that twist at the end while I wear them.

Is there any way to straighten them? Would an iron straighten them out?

UPDATE: ADDED PICTURES

Video Picture

  • It will be great if you provide some pictures for the same. – MANEESH MOHAN Dec 30 '16 at 3:19
  • 1
    Iron it bro-dawg, it can be done! youtube.com/watch?v=bIGAsIx7alM – digiliooo Dec 30 '16 at 20:34
  • Actually, I retract that last comment, and am in agreement with @maneeshmohan. Without pictures of said neckties, this debacle may never get resolved. – digiliooo Dec 30 '16 at 20:44
  • @MANEESHMOHAN - pictures added – dochoffiday Jan 3 '17 at 15:20
  • @digiliooo - pictures added – dochoffiday Jan 3 '17 at 15:20
2

Ironing may help but seeing the pictures I fear poorly made tie to start with.

If it was an expensive tie, bring it to the shop (or the chain of shops) you bought it.

When not returning them to the shop, check the washing information on the tie. If it is dry cleaning only, and you can not wear the tie as it is, try dry ironing. If you can wash it, wash as per information label and iron.

In ironing, gently push it to get it flat again.

If the twist orginates from the knot with which you tie your tie, you can try a different knot and try to close it less tight.

And have you tried a tie pin to keep the tie in place even though it wants to turn?

1

The problem is the way the necktie was assembled. You can fix it; but, the effort won't be worth it unless the tie has sentimental value. If you look at the back of your neck-tie you'll see the two sides of it are "tack-stitched" together where they meet. The bar-shape tack-stitch holds too securely to allow each side to "give" enough to lie flat after a few uses.
Remove the tack-stitch and iron the tie and bunting inner liner; then, reassemble it: fold the sides together and baste them with a single thread rather than tack the sides.

You can avoid the problem by ensuring your neckties are "single thread." Single-thread neckties are folded lengthwise on either side to meet. A single thread is bast-stitched to either side to close the folded tie shut. The thread is not attached but allowed to just hang. The single thread gives your garment some "give" so asymmetrical knots don't twist the threads of the necktie. They are usually a bit more expensive because this cannot be automated. A person must finish the garment. Since it costs more anyway, better materials can be used as they are a smaller fraction (proportionally) of the cost of manufacture. Next time you find yourself in a mens store, ask the salesperson to show you the details of assembly.

You can hack the problem by fastening the tails of the necktie to your shirt with a tie-bar.

Some neck-ties have a loop for the smaller end to hold it in place behind the wider end. In addition, some have a series of button holes to attach to your shirt button.

0

Iron it, You have to be careful though.

  • Because it will melt if you don't! – L.B. Jan 4 '17 at 16:41
  • Could you add some more detail to this answer? It's been automatically flagged as low-quality. – Rand al'Thor Jan 5 '17 at 1:28
  • @richard the same was told by previous answerer, better you update the answer or the same will get further more negative points – MANEESH MOHAN Jan 5 '17 at 3:02
0

I have to reccomend a tie bar / tie clip as the best solution to (reproducibly, and with minimum effort) solve your problem. There are plenty of cheap examples available online, and they can range from quite plain and unobtrusive to the slightly more gaudy examples shown on wikipedia.

(Credit to Willeke's answer, as they mentioned tie pins briefly.)

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service, privacy policy and cookie policy

Not the answer you're looking for? Browse other questions tagged or ask your own question.