22

As the question states, I am looking to remove a thoroughly stripped screw (the head is stripped) from a hard disk drive. My main issue is that I have no power tools available to remove the screw. How might I be able to remove the screw without drilling it out?

10

You can use a good knife or other very sharp and very hard tool and make small parallel scratches on the screw (whatever is left of it), alternatively one deeper scratch in the middle. Then use the hack of abby and a flat tool. I found it most useful to use the inbus (hexagonal screw) bit of my tools to be perfect for this. Depending on the situation you have at hand a rounded tool may be of more use.

You need to apply a lot of downward force on the tool to do this.

That way you will press the rubber band into the small scratches and when you turn the tool it will start twitching slightly. This takes some time to produce results but works. You can monitor the progress if you make the scratches parallel to something nearby.

This assumes the screw will turn at all, so you might need to lubricate it before doing this. If its rusted in or otherwise totally unturnable, you might have lost.

  • "hack of abby" that answer is missing! – Santropedro Dec 15 '18 at 11:12
  • 1
    @Santropedro 'abby' was part of the nick of the user 'hairboat' when I wrote this answer. I added a link. – Angelo Fuchs Dec 15 '18 at 16:23
  • I agree, hairboat=abby. It says on her profile. – Santropedro Dec 15 '18 at 23:07
29

Try placing a rubber band between the head of the screw and the screwdriver.

enter image description here

This usually helps increase friction.

  • I do believe I have stripped it beyond that. – L.B. Dec 10 '14 at 3:10
  • 1
    @L.B. Yea, I don't think this would work that well on really stripped heads. – CRABOLO Dec 16 '14 at 6:43
  • 1
    @abby hairboat can you explain bit more detailed how does rubber helps?Sounds interesting but cant imagine how it helps – python starter Feb 6 '15 at 21:10
  • @pythonstarter Rubber has really good friction. Have you tried rubbing rubber over some surface? It grabs really well. In this case, the rubber band is also pressed down into what remains of the head's crack (whatever that thing is called), producing better grip. – Justin Feb 7 '15 at 0:35
8

If the head is not counter sunk, a pair of lock grip pliers (vice grips) can be used to grasp the head of the screw and turn it.

4

The correct screwdriver should be used, first of all. Often times the correct screwdriver will grab the screw when it appears stripped. A sharp screwdriver should also be used, not having rounded edges. A correct screwdriver generally involves using a phillips instead of a reed-and-prince which has a sharper point, and a #2 screwdriver instead of a #1. Very seldom is a #1 screw found on a computer. Screws may be small, but are still #2. If a #2 even begins to fit the screw head, it is a #2 screw. The same cannot be said for #1.

In the Air Force I learned the correct way to remove a screw. Many seemingly stripped screws can be removed this way. As mentioned, use the correct screwdriver. Second, apply downward force. Third, bump the screwdriver and do not twist. Usually a slight grab can be felt, but the screwdriver rotates off of it. That slight grab can be exploited. By using a sharp screwdriver and bumping it, going back and fourth, that slight grab will wear into a shoulder large enough to wind the screw with. It takes a certain feel to do this which is not hard to acquire.

I want to follow up by saying how to prevent stripping a screw. Go ahead and twist most of the way in. When it gets to the last and starts becoming tight, stop twisting and start bumping. Use small bumps and never large moves.

  • Wow! I never knew any of that! Thank you for the information, I will keep that in mind for future reference! – L.B. Feb 6 '15 at 22:30
1

How about trying to epoxy or super glue a tool to the screw? Or glue something to what's left of the screw so that you can grip it with pliers or a wrench?

This can be precise work, so you might want to mask off areas you don't want to get adhesive on. You could use what ever you are going to glue to the screw as a punch through the masking tape to create the mask.

1

I know this is very late, but I know a great hack for this. All you need a matchstick. All you have to do is use the square bottom of the matchstick and put it in the screw. Now, you can get the screw out by using the match like a normal screwdriver.

match

  • Wow! That is so cool! I never would have thought of that! – L.B. Feb 26 '15 at 0:50
1

there is a tool called an easy-out that you can stick into the chewed-up screwdriver hole of a phillips-type screw head and, grasping the easy-out with a pair of pliers, unscrew the stuck screw. It may be difficult to find one small enough for your hard drive, but well-equipped hardware stores have them in a variety of sizes.

  • 1
    They are also called "screw extractors." They have a reverse strew thread that digs into the worn driver socket as you twist to remove the screw. – Stan Oct 8 at 14:47
  • exactly right @stan – niels nielsen Oct 9 at 5:48
1

Don't forget that you can cut a slot into the head of any screw with a worn socket. A small grinder such as a Dremel Tool, or a fine-tooth hacksaw if you can get at the head of the screw or don't mind defacing the surround especially if it's a washer or bezel that can be replaced.

Also, there are various other shaped driver blades that could fit a worn/stripped Phillips, posi-driver, or screw-lox screw head socket such as a square-head Robertson driver.

Good luck.

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service, privacy policy and cookie policy

Not the answer you're looking for? Browse other questions tagged or ask your own question.