13

I misplaced my allen wrench set. I'm not going to buy a new one, because I haven't given up hope on finding the old one.

In the meantime, what can I use as an allen wrench substitute? I tried using the prong of a fork (for a small hex-socket) with limited effectiveness and wear to the socket. I haven't thought of anything to try for larger sockets.

  • 5
    Just buy a spare set. A basic one should only cost you a few dollars. (Here's a 30-piece set I found for $6 in a few minutes of searching.) All the hacks below are only reasonable if you need one right now and can't stop by a hardware store to get one. – Ilmari Karonen Dec 27 '14 at 19:57
11

A few sites recommend using a flat head screw driver. Find one that fits tightly across the inside of the hex head going from corner to corner and turn it gently.

Personally I would go with a Torx bit. If you have an electric drill check the bits that came with it, there's a good chance that you have some. They will work for hex bolts with a lot less slipping than a flat head.

enter image description here

3
  • Find a bolt whose head is the required size. Insert the bolt head half-way into the socket. Apply an adjustable wrench or pair of visegrips to the sticking-out half.

  • Find a bolt whose head is the required size. Turn two nuts on and counter-tighten them (jam them together). Insert the bolt head into the socket. Apply an adjustable wrench or pair of visegrips to the appropriate nut (depending on the direction of force, choose the nut that tightens the jammed pair, not loosens them!).

  • You can get a decent set of hex wrenches for $10 - $15; possibly much less if you wait for a sale. Save yourself time and aggravation and just get them (good tools are half the battle!).

Hope that helps!

1

One way to make an improvised allen wrench is to take a plastic ballpoint pen and remove the ink cartridge and writing tip.

Then you can take a lighter and gently heat the end of the pen tube with a lighter, being careful not to burn it and soften the plastic. When the plastic begins to soften, you will then insert the end of the pen into the head of the allen screw. Make sure that you push it in all the way, and then hold it there until the plastic hardens. You should only do this in a well ventilated area because the fumes are toxic.

Once it has hardened, it will take the form of the screwhead and it should be a perfect allen wrench. Different types of pens will work better than others. An old Bic pen with soft nylon plastic will work the best since it won't be too brittle and break off as easy.

  • Very clever, and using the most likely things anyone would have around the house! – Y     e     z Dec 28 '14 at 3:11
1

If I am understanding your problem correctly then you could:

a pencil being used to unscrew a screw

Make an Emergency Hex Key / Allen Wrench: This can be done by cutting the pointy writing tip off a pencil and cutting the edge down until it will fit. Pieces of wood of certain sizes can be used, as well. A plus is that the pencil can be reused afterwards.

Shave the sides of the pencil down to size. Keep the peelings parallel to the faces. Make your shavings pretty thin. Test to see if it fits. If it's tight, that's good.

Different types of screwdrivers are said to work, as well.


Additional Info

5 Ways to Improvise an Allen Wrench

A good example for smaller allen wrench nuts, you could likely use a set of flat-tipped tweezers, or even the flat edge on a pair of finger nail clippers. There are numbers of bathroom items that can be used in such cases, and again it is about being able to turn or spin this screw, nut or bolt to get it loose.

Sometimes you can use small types of flat headed screwdrivers as an allen wrench by putting the end in the socket so that the 2 edges of the screwdriver work as leverage in the hole to turn it. A wider socket on the bolt or nut, use a wider flathead screwdriver. The object here is to wedge the screwdriver into the hex of the bolt, to create torque so it can be unscrewed.

You can also find great improvised allen wrench type devices in your kitchen cupboard or in the silverware drawers. Flat tipped and strong pairing knives could potentially work depending on the gauge and depth of the hex screws hole. Remember you are simply trying to wedge your tool into the hex so that you can spin or turn it

0

Using a Dremel with a cutting disk, I've sawed a slot across the head and then used a standard flat screw driver. Also done this with warn phillips head screws. If the screw head is exposed above the work surface, could also use a hack saw to make a slot.

protected by Community Jul 7 '18 at 0:39

Thank you for your interest in this question. Because it has attracted low-quality or spam answers that had to be removed, posting an answer now requires 10 reputation on this site (the association bonus does not count).

Would you like to answer one of these unanswered questions instead?

Not the answer you're looking for? Browse other questions tagged or ask your own question.