I've just acquired and finished setting up a new wooden plank computer desk. Upon finishing the new setup I naturally went to use my keyboard and noticed that the wooden planks aren't exactly flush resulting in my keyboard wobbling with each keystroke as shown below.

What simple solutions could I implement to my keyboard to stop this from happening? I'd like to keep the solution's visibility minimal.

I've contemplated using Sticky Tack to level the keyboard but the thought of seeing a blue blob on the bottom of my keyboard daily does not blend well with my OCD.

animated keyboard wobble

  • 2
    Does sticking a square of cardboard or some soft white padded thing underneath it not work for you for some reason...? Commented Jun 13, 2015 at 22:50
  • 4
    Also white sticky tack is not blue; when you looked for white sticky tack, which I presume you did, is there a reason you did not find it sufficient? Also, is using it in a different place on the desk an option? Commented Jun 13, 2015 at 23:34
  • 2
    Is turning the table around 180° a option? That could fix the problem.
    – Ian
    Commented Jun 14, 2015 at 9:17
  • 1
    In an ideal world, keyboard manufacturers would design keyboards to be supported on three points. Never a chance to wobble. Commented Jun 14, 2015 at 9:17
  • 3
    Is there a sudden world shortage of beermats? Commented Jun 15, 2015 at 20:43

15 Answers 15


This is happening because there is a gap of space between a corner of your keyboard and the desk.

Your goal, as you may have guessed, is to remove this gap.

A general solution is to look around you and find a material that can do this. Look around you for something with the following qualities:

  • Small.
  • As thick as the gap.
  • Solid at room temperature, occupying a region of the known universe's three spacial dimensions. Ideally low enough density that its mass does not exert a significant gravitational pull on surrounding objects.
  • Non-toxic through skin contact. Non-toxic to any pets you may have.
  • Stable (non-radioactive), inert (non-reactive, at least with your desk, keyboard, and air), and either non-magnetic or possessing a magnetic field with an intensity low enough to not damage nearby sensitive objects.
  • Composed of little or no saccharides (sugars), proteins, and/or lipids (fats), which may attract ants (relevant to me, at least), roaches, or other pests. (Example: Do not affix a small piece of meat to your keyboard with honey.)

Sometimes you may look around you and find something that is the appropriate thickness but perhaps too large. If you find materials like this, look for one that you can cut with a tool. Examples of tools that cut things are:

  • Scissors.
  • Knives.
  • Generally anything harder than the material you wish to cut with a wedge-shaped edge that can be driven into the material to separate it.

Some materials can even be torn by hand.

Another option is something larger but soft, so that it can deform to an even surface. Many such things exist. Things like mouse pads, placemats, pieces of random soft material that you may have laying around or see online. Using imagination and your lifetime's worth of experience with physics, you should be able to find such a material.

Once you find this material, insert it into the gap or under the keyboard.

"But wait!" you say, "Every time I move my keyboard, the material slips out!" Well, as you may have noticed throughout your life, the problem of preventing one thing from moving relative to another thing has many established solutions. Your goal is to find some sort of material or compound that will allow your chosen gap filler to remain in place relative to the desk or keyboard. For inspiration, your local dollar store's school supply section or local hardware store's adhesive section may be of use.

Some materials may not even need to be cut, and may fit all of the above requirements. For example, using my power of logical thinking, and remembering things that I have seen before, I am able to recall that these are possible options. Perhaps you have some laying around that you haven't used.

Of course, the "best" (that is, it'll really solve the issue) option is to level your desk, for which tools such as hand planes exist (if you find the video unsatisfying, there are others in the related video list), as leveling uneven wood is also a problem with well-established solutions. If the desk already has a finish, though, you'd have to refinish it. Still, a job well done can be fun and satisfying.

Alternatively, if you purchased the desk new, and it is warped, consider exchanging it for one that is not warped.

  • 9
    This is almost too in depth for trying to find something to stop a keyboard from wobbling. lol Commented Jun 14, 2015 at 0:04
  • 11
    @FarazMasroor An in-depth explanation seemed called for as this is obviously a complex problem. Commented Jun 14, 2015 at 0:29
  • 3
    With a name like captain obvious, I'm not sure you share the same definition of obvious...
    – Aron
    Commented Jun 14, 2015 at 13:15
  • 4
    * removes meat and honey * Commented Jun 15, 2015 at 11:28

Why don't you put one cloth (little bit thick just like towel) flat on your table and then put your keyboard on it. If it works then great but if it wobble again then fold cloth from that end where it is wobbling and then you will get leveled keyboard easily and you can adjust by your own. This is the only simple way to stop keyboard wobbling.

Here is the image which are kept just at front edge of keyboard.

enter image description here

enter image description here


I realize that the question states "I'd like to keep the solution's visibility minimal" as one of the goals, and plenty of other answers have suggestions for modifying the keyboard, but I'm going to make a case here for instead modifying the desk, while focusing on the solution being visible-but-attractive, rather than invisible.

Using a keyboard on an uneven surface is just unpleasant, all of the shimming and bracing in the world can't change that, and those solutions tend to become further annoyances over time. Shims slip, keyboards shift, etc.

Much better to give the desk a flat, level surface, on which to set the keyboard. You can get quarter-inch steel plate from plenty of places (probably even Home Depot) for not very much money. (12" x 18" is a standard-ish size, and runs around $20-$25 US. That would be more than enough space for the Apple wireless keyboard. You could probably even get away with 6" x 18", since it won't really need to move front-to-back much.)

Get a nice, clean, flat quarter-inch steel plate, set it on the desk as the "keyboard tray", and use some rubber feet or similar to make sure the plate sits flat and level. It's not likely to bend, and it's not going anywhere. (If you want to be really sure and don't mind gluing to the desk surface, some Liquid Nails should hold it.)

Your keyboard should now sit perfectly stable, and the plate's only 1/4" thick so you won't even notice it when typing.

That's what I'd do, if this was the desk I'd be using my computer on every single day.

You could also do the same thing with a sheet of glass, but it'd have to be thicker and it's harder to hide anything placed underneath to level it. (Unless you wanted to get a glass top cut to fit the entire desk, which would be an expensive but attractive way to get a really flat surface.)

  • 1
    This is a good plan and would make for a fun project.
    – chicks
    Commented Jun 15, 2015 at 5:06
  • 1
    "Unless you wanted to get a glass top cut to fit the entire desk" -- in which case you almost might as well get a glass desk. Commented Jun 15, 2015 at 13:37

If you slowly begin turning your keyboard on its vertical axis, it will come to a stable resting point before you've made a quarter turn.

enter image description here

Perhaps not the most convenient for use, but it fits the criteria of your question ;) And who knows, maybe you'll get lucky and only need to turn it a few degrees.

Source: https://www.youtube.com/watch?v=OuF-WB7mD6k

Scientific paper: http://arxiv.org/pdf/math-ph/0510065v6.pdf

  • I don't think it necessarily always works with a full plane or two continuous lines of contact. Just four contact points like a table. But if you put four rubber feet or something on the corners of the keyboard then it would work. Commented Nov 30, 2015 at 23:46

I have a piece of non-slip grip mat under my keyboard. Not only does it stop this problem, it makes the keyboard much quieter and more pleasant to use.


A simple solution would be to place a shim of the correct height under the keyboard. Because the keyboard won't always be in exactly the same place, you need to be able to adjust the height of the shim. Something like sticky tack is a good solution. If you place the sticky tack under the battery holder, it won't be visible when you're using the keyboard.


The obvious solution is to use a laser keyboard. It eliminates all incompatibilities between physical keyboard and desk. Here's a really cool one:

enter image description here

  • 2
    Apparently those keyboards suck. No physical feedback.
    – HarryCBurn
    Commented Aug 2, 2015 at 23:29
  • Though this provides a solution to the OP's problem, it does not actually answer the question that he asked here. He wants to know how to stop the wobble of a keyboard and I don't think that buying a laser keyboard is the solution he is looking for.
    – michaelpri
    Commented Aug 15, 2015 at 2:04

Place a lump of blue tac in the centre of the bar that runs the whole way along the back of the keyboard. That would make a tripod, and tripods don't wobble.

To aid in quietness etc, place a piece of felt on the blue tac.


Get a long stick (longer than the diagonal of the KB) and half the thickness of the gap. Place it diagonally under the KB. Have it fitted with magnets, so it can stay with the KB, which you might have to attach two metal pieces to somehow. Everything can be painted in an OCD pleasing colour.


If the keyboard is dedicated to that desk, you could just simply bend the keyboard...

  • 1
    By heating, I presume? Commented Jun 15, 2015 at 21:08
  • @DrMoishePippik maybe it's a joke since the new large iphone had a bending problem?
    Commented Jun 16, 2015 at 6:16
  • 1
    I've known the keyboards depicted in the picture to be susceptible to bending, and not isolated to only my experiences. e.g. forums.macrumors.com/threads/… Commented Jun 16, 2015 at 20:49

That gap isn't very large. You can twist your keyboard by hand in small increments to fit the surface of your table. The keyboard may appear fairly stiff, but it will conform to the table with some effort.

A better course of action, though, is to get a Bench Plane and simply flatten the surface of the table, at least around the keyboard area. Shouldn't take too long.


If I came upon this situation, I'd just use a blob of epoxy putty on the far right corner to even things up. Gluing any kind of spacer on that corner would work as well, and be out of sight. Then I'd enroll in your local adult education class in cabinetmaking to prevent future irritations :-)


Get a piece of double-sided tape. Stick one side of it to the keyboard. Leave the backing on the other side so it doesn't stick to the desk.

  • 2
    @michaelpri They're saying get a piece of double-sided tape. Stick one side of it to the keyboard. Leave the backing on the other side so it doesn't stick to the desk. It's really just a double-sided tape option in this poll question asking "What is your favorite object that takes up space?" Vote here if double-sided tape is your favorite object. +1 from me, I think double-sided tape is super cool. Commented Jun 13, 2015 at 23:17
  • 1
    @CaptainObvious Had he explained it like that, I would have also upvoted, as it is an interesting idea, just not a good answer.
    – michaelpri
    Commented Jun 14, 2015 at 2:23

Sorry if this is making your OCD worse, but I think the problem is that your table is standing imbalanced. You should first attack that.

The keyboard is in itself well balanced, so any solution you find for the current position on the table will probably not work 20-30 cm to the left or the right or when you move the keyboard to the middle of the table to put a book or piece of paper in front of you.

In your screenshot you either have to lift the front left leg or the back right one to make it even again, use some marbles or a water level to find out which one. On most phones there is an app, that if you calibrate it right works pretty good. It might also happen that you need to adjust 3 of the 4 table legs.

It could also be the floor that's wrong, so any solution you find for the table ... :)

  • 1
    It depends. If there is a gap then either the keyboard or the surface of the desk is curved. If the surface of the desk is not flexible then no amount of adjusting leg heights will remove the curve. Commented Jun 13, 2015 at 23:36

Get a piece of aluminum foil and fold it until it is big enough for you to put it under the keyboard and keep it stable.

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.